金沙官网

欢迎光临金沙网站建筑装饰工程有限公司 ! 收藏网站收藏网站 在线留言在线留言 联系我们联系我们

富美家中国战略合作伙伴 C CTV专访品牌
产品/加工技术热线: 18560211715
0531-85925226
大家都在搜:
您的位置: 首页 > 新闻动态>>防火板的技术的保养维护特点

防火板的技术的保养维护特点

来源:/ 日期:2019-06-03
   首先说一下搬运:
First, let's say moving:
防火板的板材尺寸一般是1220mm*2440mm,尺寸相对来讲比较大,一个人不好拿,所以在搬运过程中比较好是两个人,分别站在防火板两端,让防火板形成拱形 ,再进行搬运,如果厚度太薄且板材不多,则可以将板材卷成直径约60cm,表面朝里卷的卷筒进行搬运。如果使用绳子打结固定,在绳子与板材尾边接触的地方要垫硬纸板以防止板材破裂;固定好后可有一人或者两人搬运。如果量比较大需要用到叉车时,要注意底板的大小一定要与板面大小相当!
Fire board plate size is generally 1220mm*2440mm, the size is relatively large, a person is not good to take, so the best in the handling process is two people, stand at both ends of the fire board, let the fire plate arch, and then carry, if the thickness is too thin and not much plate, then the plate can be rolled into a diameter of about 60cm, The surface of the roll is carried on the reel. If the rope is tied and fixed, the cardboard shall be padded to prevent the plate from breaking down in the place where the rope is in contact with the end of the plate. After the fixation is fixed, one or two people can be carried. If the forklift is larger, it should be noted that the size of the floor must be the same as that of the board.
提示:防火板的表面处理丰富多样,色彩鲜明,搬运时切忌不可一个人拉住一边在地上拖拽前进,避免损伤防火板表面,以至于影响装修效果。
Hint: the surface treatment of the fire prevention board is rich and diverse, and the color is distinct. Avoid pulling and dragging one side on the ground, avoiding the damage of the surface of the fireproof board, so as to affect the decoration effect.
其次是储存:
The next is storage:
富美家
防火板在储存是应以水平、面对面、背对背的方式存放,并在上面放置垫板。储存场所的选择要注意避光、防潮、防热。防火板材也不要与地面或者外墙直接接触,为了储存期间不影响板材的质量,存放区的温度比较好不要低于18℃,相对湿度不要低于50%。
The fireproof boards should be stored in horizontal, face-to-face, back to back mode and placed on the top. Attention should be paid to avoiding light, moisture-proof and heat protection. The fireproof plate does not contact with the surface or the exterior wall directly. In order to store the quality of the plate, the temperature of the storage area should not be lower than 18 C, and the relative humidity should not be less than 50%.
防火板在贴面加工过程中,比较好使用万能胶或者白胶作为粘合剂,在裁剪时要预留6mm左右的修边区域,比较好不要按照板面大小一丝不差的切,裁切过程中要用碳钢制品并从正面进刀。 然后在磨平的基材表面均匀布胶,使用万能胶时以手背接触布胶表面不粘手时为宜,使用白胶时需要经行冷压粘贴。冷弯处理时,将胶水涂在耐火片背后,再将胶水涂在需弯曲处,用滚筒顺着弯度滚压粘合。使用修边机从防火板和基材贴合的边缘上清除溢料或毛刺。如果没有修边机,也可以用较为锋利的锉刀将多余部分去除。
In the process of veneer processing, it is best to use the glue or white glue as adhesive. In the cutting, it is necessary to reserve the trimming area of about 6mm. It is better not to cut the size of the plate, and the carbon steel products should be used in the cutting process and from the front. Then the surface of the base material is evenly distributed, and when it is used, it is suitable to contact the surface of the cloth with the back of the hand. When using the white glue, it needs to be pressed by cold press. When cold bending is applied, the glue is applied to the back of the refractory, then the glue is applied to the bending point, and the roller is rolled and glued along the camber. Use trimming machine to remove spills or burrs from the edge of the lamination of the fireproof board and the base material. If there is no trimming machine, a more sharp file can be used to remove excess parts.
一般防火板贴墙时应切割为600mm的宽度;若每片墙面的宽度超过600mm,则应该事先进行胶合加工,使用尿素胶,防火板需要使用0.8mm以上;若一定用强力胶,则在胶合压力时使用机器压力滚轮。
The general fire board should be cut to the width of 600mm when the wall is attached to the wall; if the width of each wall is more than 600mm, it should be glued in advance and use the urea glue. The fireproof plate needs to use 0.8mm above. If a strong adhesive is used, the machine pressure roller is used in the bonding pressure.

全国服务热线

18560211715
XML 地图 | Sitemap 地图